How to Reset Router Password

Setup Mode

Cisco devices include a feature called Setup mode to help you make a basic initial configuration. Setup mode will run only if there is no configuration file in NVRAM—either because the router is brand-new, or because it has been erased. Setup mode will ask you a series of questions and apply the configuration to the device based on your answers. You can abort Setup mode by typing CTRL+C or by saying "no" either when asked if you want to enter the initial configuration dialog or when asked if you want to save the configuration at the end of the question.

Configuration register

The configuration register is a special register in the router that determines many of its boot up and running options, including how the router finds the IOS image and its configuration file. The configuration register is a four-character hexadecimal value that can be changed to manipulate how the router behaves at bootup. The default value is 0x2102. 
The characters "0x" indicate that the characters that follow are in hexadecimal. This makes it clear whether the value is "two thousand one hundred and two" or, as in this case, "two one zero two hexadecimal". 
The fourth character in the configuration register is known as the boot field. Changing the value for this character will have the following effects:

·         0x2100 = Always boot to ROMMON.

·         0x2101 = Always boot to RXBOOT.

·         0x2102 through 0x210F = Load the first valid IOS in flash; values of 2 through F for the fourth character specify other IOS image files in flash.

The third character in the configuration register can modify how the router loads the configuration file. The setting of 0x2142 causes the router to ignore the startup-config file in NVRAM (which is where the password is stored) and proceed without a configuration—as if the router were brand new or had its configuration erased.

How to reset Router password

The Password Recovery process is simple and takes less than five minutes depending on how fast your router boots

·         Connect to the console port, start your terminal application, and power cycle the router. When you see the boot process beginning, hit the Break sequence. (This is usually Ctrl+Page Break, but it might differ for different terminal applications.) Doing this interrupts the boot process and drops the router into ROMMON.

·         At the ROMMON prompt, enter the command confreg 0x2142 to set the configuration register to 0x2142.

·         Restart the router by power cycling it or by issuing the command reset.

·         When the router reloads, the configuration register setting of 0x2142 instructs the router to ignore the startup-config file in NVRAM. You will be asked if you want to go through Setup mode because the router thinks it has no startup-configuration file. Exit from Setup mode.

·         Press Return and enable command enable to go into privileged EXEC command mode. No password is required because the startup config file was not loaded.

·         Load the configuration manually by entering copy startup-config running-config.

·         Go into the Global Configuration mode using the command configure terminal and change the password with the command enable password password or enable secret password.

·         Save the new password by entering copy running-config startup-config.

·         Go to the global config prompt, and change the configuration register back to the default setting with the commandconfig-register 0x2102. Exit back to the privileged exec prompt.

·         Reboot the router using the reload command. You will be asked to save your changes; you can do so if you have made additional configuration changes.

Reset password on 1841

System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)

Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory.

Self decompressing the image :

################

monitor: command "boot" aborted due to user interrupt

rommon 1 > confreg 0x2142

rommon 2 > reset

System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)

Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory.

Self decompressing the image :

############################################################### [OK]

Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M),

 Version 12.4(15)T1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 18-Jul-07 04:52 by pt_team

Image text-base: 0x60080608, data-base: 0x6270CD50

Cisco 1841 (revision 5.0) with 114688K/16384K bytes of memory.

Processor board ID FTX0947Z18E

M860 processor: part number 0, mask 49

2 FastEthernet/IEEE 802.3 interface(s)

191K bytes of NVRAM.

31360K bytes of ATA CompactFlash (Read/Write)

Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M),

 Version 12.4(15)T1,  RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Wed 18-Jul-07 04:52 by pt_team

         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable

Router#copy startup-config running-config

Destination filename [running-config]?

428 bytes copied in 0.416 secs (1028 bytes/sec)

Router#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#enable password vinita

Router(config)#enable secret vinita

Router(config)#config-register 0x2102

Router(config)#exit

Router#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Router#reload

Proceed with reload? [confirm]